Danfoss RA 2000 manual

Installation, temperature setting, limitation and blocking, theft protection

To remove the thermostat turn

the base counter-clockwise.

This will also reset the the

snap-action mechanism when

an audible "click" is heard.

Installation

Limiting and blocking the setting range

Theft protection

Remove the cover and install the theft

protection button, code 013G5245

without pushing it all the way in.

Once the thermostat is mounted on

the valve, push in the theft protection

device. The thermostat cannot be

removed.

Lower limit setting (min. setting)

Locking setting

Example: Required locked value = “3”

- Set thermostat at “3”

- Remove both pins from the the ther-

mostat.

- Place one pin under the diamond mark

and the othger pin under the triangle

mark.

Example: Required min. value = “2”

- Set thermostat at “2”

- Remove a pin from the bottom of the

thermostat with a screwdriver and

mount it under the triangle mark on

the knob (between setting positons

2 and 3).

Example: Required max. value = “4” -

Set thermostat at “4”

- Remove a pin from the bottom of the

thermostat with a screwdriver and

mount it under the diamond mark on

the knob (between setting positons 1

and 2).

Upper limit setting (max. setting)

To remove the theft protection use

screwdriver 013G1236 and screw into

the hole (1). Pulled out until the stop is

reached (2).

Temperature setting

The required room temperature is

obtained by turning the thermostat

knob. The numbers on the dial cor-

respond to the approximate tem-

peratures of the scale.

The temperatures indicated are

guidelines only. The actual room tem-

perature will depend on structural fac-

tors affecting the thermostats, location,

 = Frost protection setting

The remote sensor must not

be in a drafty location or be

covered. Do not install above a

heat source. Attach the sensor

bracket to the desired location.

Pull out the required length of

capillary tube and secure to

the sensor as shown. Push the

sensor onto the base.

Remove the valve cover.

Check that the thermostat is

set at the factory setting of 5.

Push the thermostat firmly

onto the valve until an au-

dible "click" is heard.

Manual

View the manual for the Danfoss RA 2000 here, for free. This manual comes under the category thermostat and has been rated by 5 people with an average of a 7.3. This manual is available in the following languages: English. Do you have a question about the Danfoss RA 2000 or do you need help? Ask your question here

Need help?

Do you have a question about the Danfoss and is the answer not in the manual?

• Receive updates on solutions
• Get answers to your question

Question and answer

Hello We have a radiator with a Danfoss thermostat (an older model, see attached image). The radiator is not functioning even though it is set to maximum. I remember that the previous issue was that a spring had gotten stuck. Is this something that can be fixed by oneself and if so, how? Kind regards, Per T

This message has been automatically translated

How do you increase the flow on this one, picture below? My "handyman" says you can turn the wheel without the cable moving, which doesn't work. Do you need to loosen the brass nut?

This message has been automatically translated

the big yellow knob and the black arrow move separately. which position do i have to get them in to set the thermostat to 4?

2 comments

The position of the thermostat to set it to 4 is the "3 - 4" position on the control scale.

This answer is automatically generated

Did you figure it out. I have the same problem.

I have an old thermostat Ra 2000. How do I loosen it so I can check the spring in case it is stuck? I don't dare to touch too much since the "threaded screw" itself is made of plastic.

This message has been automatically translated

How to turn the temperature down

Danfoss RA 2000 specifications

Below you will find the product specifications and the manual specifications of the Danfoss RA 2000.

The Danfoss RA 2000 is a programmable thermostat that is designed to control the temperature in homes and businesses. This device is made of high-quality materials, ensuring its long-lasting durability. The thermostat's sleek and compact design makes it easy to install and operate. It features a clear and user-friendly interface that makes programming and adjusting the temperature a breeze. The Danfoss RA 2000 can be programmed to turn the heat on and off automatically, which can help save energy and reduce utility bills. The device is compatible with a wide range of heating systems, including radiators, floor heating, and baseboards. It can also be configured to suit the specific needs of the user, allowing for customized temperature controls throughout the day. In addition, the RA 2000 features a built-in frost protection function, which prevents the temperature from dropping below freezing during cold weather. This feature also helps to protect pipes and other components from damage, saving even more money on potential repairs. Overall, the Danfoss RA 2000 is a reliable and efficient thermostat that can help make any home or business more comfortable and energy-efficient.

Frequently Asked Questions

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Danfoss RA 2000 below.

Where is the best location to place the thermostat?

The best place for the thermostat is the room where you spend the most time, in many cases the living room or kitchen. Place the thermostat about one and a half metres above the floor, not in the sun and not on an outside wall.

What is the dead band of a thermostat?

If your thermostat has a dead band, your installation is, as it were, 'at rest'. The thermostat only switches on when, for example, the difference deviates more than 2˚C from the set room temperature.